RoE | Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Information ======

  * Diagnostic commands for AMD graphics cards

====== AMDGPU ======

===== References =====

  * https://wiki.archlinux.org/index.php/AMDGPU#Overclocking

===== TODO =====

  * https://blog.tingping.se/2018/12/01/amdgpu-fullrgb.html

===== Query =====

==== Power Info ====

****

  sudo watch --interval '0.5' cat '/sys/kernel/debug/dri/0/amdgpu_pm_info'

==== Power Sates ====

****

  cat '/sys/class/drm/card0/device/pp_od_clk_voltage'

===== Overclock =====

==== SCLK ====

  * ''7'' is the highest available ''PSTATE'' for ''SCLK''
  * ''1386'' is the value for ''SCLK'' for that ''PSTATE''
  * ''1155'' is the voltage/''VDDC'' for the specified ''SCLK'' for that ''PSTATE''
  * When the highest ''PSTATE'' is used, the GPU Core will run at 1386MHz @ 1155mV
  * :!: This does **not** take effect immediately

  echo 's 7 1386 1155' | sudo tee '/sys/class/drm/card0/device/pp_od_clk_voltage'

==== MCLK ====

  * ''2'' is the highest available ''PSTATE'' for ''MCLK''
  * ''2025'' is the value for ''MCLK'' for that ''PSTATE''
  * ''955'' is the voltage/''VDDC'' for the specified ''MCLK'' for that ''PSTATE''
  * When the highest ''PSTATE'' is used, the GPU Memory will run at 2025MHz @ 955mV
  * :!: This does **not** take effect immediately

  echo 'm 2 2025 955' | sudo tee '/sys/class/drm/card0/device/pp_od_clk_voltage'

==== Verify Values ====

  * :!: Check if the specified values look alright

  cat '/sys/class/drm/card0/device/pp_od_clk_voltage'

==== Commit ====

  * :!: Be absolutely certain the values above looked alright
  * :!: It is **very** well possible to destroy hardware with this if the values are too high

  echo 'c' | sudo tee '/sys/class/drm/card0/device/pp_od_clk_voltage'

==== Verify Clocks ====

  * Runs ''glxgears'' without VSync, thus allowing the GPU to enter the highest ''PSTATE'' automatically
  * Queries power info live every 0.5s

  vblank_mode='0' glxgears

  sudo watch --interval '0.5' cat '/sys/kernel/debug/dri/0/amdgpu_pm_info'

==== Reset Clocks ====

  * Sets all CLKs and VDDCs to card defaults and commits it

  echo 'r' | sudo tee '/sys/class/drm/card0/device/pp_od_clk_voltage' && echo 'c' | sudo tee '/sys/class/drm/card0/device/pp_od_clk_voltage'

===== PSTATE Control =====

==== Manual Controls ====

  * ''PSTATE'' will be manually controllable
  * TODO: ''auto'' makes sense as the default for this?

  echo 'manual' | sudo tee '/sys/class/drm/card0/device/power_dpm_force_performance_level'

  cat '/sys/class/drm/card0/device/power_dpm_force_performance_level'

==== SCLK ===

  * Can allow either a single ''PSTATE'', or multiple to be automatically selected for ''SCLK'' based on GPU load

  echo '7' | sudo tee '/sys/class/drm/card0/device/pp_dpm_sclk'

  echo '5 6 7' | sudo tee '/sys/class/drm/card0/device/pp_dpm_sclk'

==== MCLK ====

  * Can allow either a single ''PSTATE'', or multiple to be automatically selected for ''MCLK'' based on GPU load

  echo '2' | sudo tee '/sys/class/drm/card0/device/pp_dpm_mclk'

  echo '1 2' | sudo tee '/sys/class/drm/card0/device/pp_dpm_mclk'

===== Power Limit =====

==== Query ====

****

  cat '/sys/class/drm/card0/device/hwmon/hwmon'*'/power1_cap'

==== Get Max ====

****

  cat '/sys/class/drm/card0/device/hwmon/hwmon'*'/power1_cap_max'

==== Set ====

  * :!: This makes fun assumptions, but theoretically shouldn't allow the power cap to go above levels stated in the firmware; might not be dangerous

  echo "$(cat '/sys/class/drm/card0/device/hwmon/hwmon'*'/power1_cap_max')" | sudo tee '/sys/class/drm/card0/device/hwmon/hwmon'*'/power1_cap' > '/dev/null'

  echo "$(cat '/sys/class/drm/card1/device/hwmon/hwmon'*'/power1_cap_max')" | sudo tee '/sys/class/drm/card1/device/hwmon/hwmon'*'/power1_cap' > '/dev/null'