devices:netgear_r6260_openwrt
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
devices:netgear_r6260_openwrt [2020/11/16 14:43] – Sean Rhone | devices:netgear_r6260_openwrt [2022/06/11 19:20] – Sean Rhone | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Information ====== | ====== Information ====== | ||
- | * NETGEAR R6260 ((https:// | + | * [[https:// |
- | * OpenWrt ((https:// | + | * [[https:// |
+ | * [[https:// | ||
+ | * [[https:// | ||
- | ====== Snapshot ====== | + | ===== Notes ===== |
- | ==== sysupgrade ==== | + | * 2021/04/28: Dropping invalid packets (firewall) causes an Oculus Quest 2 to not load it's own store/home page |
+ | * 2021/06/14: Enabling '' | ||
+ | * 2021/06/29: Enabling '' | ||
+ | * Stock firmware reports '' | ||
- | * This downloads the latest '' | + | ====== Snapshot ====== |
- | rm -f '/ | + | ==== Links ==== |
- | ===== Date Check ===== | + | * '' |
- | * https:// | + | * [[https:// |
+ | * [[https:// | ||
- | ===== Download ===== | + | ==== sysupgrade |
- | ==== OpenWRT ==== | + | * This downloads the latest '' |
- | | + | |
- | rm -f '/tmp/netgear_r6260-sysupgrade-snapshot.bin' && | + | rm -f '/ |
- | === SSL Support === | + | rm -Rf ~/' |
- | | + | |
- | opkg update && opkg install ' | + | ===== Packages ===== |
- | ===== Install ===== | + | * [[https:// |
- | | + | |
- | * '' | + | |
- | * '' | + | |
- | | + | |
- | | + | |
- | ===== LuCI ===== | + | ====== LuCI ====== |
- | * https://openwrt.org/ | + | * http://192.168.1.1 |
- | * :!: Snapshot images don't include LuCI, so it needs installed on **every** clean snapshot install | + | |
- | ssh ' | + | ===== DHCP ===== |
- | | + | |
- | ===== Configure ===== | + | 48 |
- | * https:// | + | ===== DNS ===== |
- | ==== Quad9 DNS ==== | + | ==== Notes ==== |
- | * https://quad9.net | + | |
+ | | ||
* See [[notes: | * See [[notes: | ||
- | < | + | ==== IPv4 ==== |
- | < | + | |
- | < | + | |
- | < | + | |
- | ==== Wireless ==== | + | * Network -> Interfaces -> LAN -> DHCP Server -> Advanced Settings -> DHCP-Options |
+ | * :!: The '' | ||
- | === 2.4GHz === | + | < |
- | * Country Code: US | + | === IPs === |
- | * [ ] Allow legacy 802.11b rates | + | |
- | * Channel: 11 | + | |
- | * Width: 40 MHz | + | |
- | * Encryption: WPA2-PSK CCMP AES | + | |
- | < | + | < |
- | === 5GHz === | + | < |
- | * Country Code: US | + | ==== IPv6 ==== |
- | * [ ] Allow legacy 802.11b rates | + | |
- | * Channel: auto ((this likely uses channel 52)) | + | |
- | * Width: 80 MHz ((160 MHz had issues)) | + | |
- | * Encryption: WPA2-PSK CCMP AES | + | |
- | <code>Highgate (5GHz)</ | + | * Network -> Interfaces -> LAN -> DHCP Server -> Advanced Settings -> IPv6 Settings -> Announced IPv6 DNS servers |
- | == Notes == | + | < |
+ | < | ||
- | * Quest 2 should be 866.7 Mbit/s on both speeds | + | ===== Wireless ===== |
- | ==== Firewall | + | ==== 2.4GHz |
- | * :!: Software and Hardware flow offloading may cause issues; this needs debugged further | + | * Advanced Settings -> [x] Disable Inactivity Polling |
- | * :!: Software and Hardware flow offloading may not offer any benefit on a 30Mbps ISP | + | * Advanced Settings -> [ ] Disassociate On Low Acknowledgement |
- | ====== Recovery ====== | + | * Country Code: US |
+ | * Channel: 11 | ||
+ | * Width: 20 MHz | ||
+ | * Encryption: WPA2-PSK CCMP AES | ||
- | ===== nmrpflash ===== | + | < |
- | * https:// | + | ==== 5GHz ==== |
- | * :!: The 2020/11/07 OpenWRT snapshot '' | + | * :!: Advanced Settings |
- | * :!: Installing the '' | + | * :!: Advanced Settings |
- | * :!: If using this, use the '' | + | * :!: These seem to fix 5GHz instability with a Chromecast |
- | | + | |
+ | * :!: Channel: 149 | ||
+ | * Width: 80 MHz | ||
+ | * Encryption: WPA2-PSK CCMP AES | ||
- | sudo '/home/ | + | < |
- | sudo '/ | + | ===== Firewall ===== |
- | sudo '/ | + | ==== Webserver ==== |
- | ====== OpenWRT Compile ====== | + | * Oak |
- | https://forum.openwrt.org/t/new-xiaomi-router-ac2100/ | + | < |
+ | < | ||
+ | < | ||
+ | < | ||
- | < | + | ==== Steam Remote Play ==== |
- | https://github.com/openwrt/openwrt/blob/master/ | + | * [[https://help.steampowered.com/en/faqs/view/0689-74B8-92AC-10F2|Steam Support]] |
- | https:// | + | === UDP === |
- | sudo dnf install gcc gcc-c++ git perl-FindBin make patch perl-Thread-Queue ncurses-devel | + | < |
+ | < | ||
+ | < | ||
- | cd ~ && mkdir -p ~/' | + | === TCP === |
- | cd ~/' | + | < |
+ | < | ||
+ | < | ||
- | cd ~/' | + | ====== Recovery ====== |
- | cd ~/' | + | ===== nmrpflash ===== |
- | | + | |
- | + | ||
- | gdma = enaled | + | |
- | dma = enabled | + | |
- | + | ||
- | + | ||
- | nano '/home/espionage724/ | + | |
- | < | + | * Reason for the '' |
- | &gdma { | + | * :!: If using an OpenWRT image, use the '' |
- | status = " | + | |
- | }; | + | |
- | &hsdma { | + | sudo ln -sv ' |
- | status = " | + | |
- | };</code> | + | |
- | menconfig | + | sudo ~/' |
- | | + | |
- | < | + | sudo ~/' |
/var/www/wiki/data/pages/devices/netgear_r6260_openwrt.txt · Last modified: 2022/12/12 02:25 by Sean Rhone