devices:linksys_ea6350_v3
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
devices:linksys_ea6350_v3 [2021/09/09 04:11] – [Wireless AP] Sean Rhone | devices:linksys_ea6350_v3 [2022/12/12 02:25] (current) – Sean Rhone | ||
---|---|---|---|
Line 14: | Line 14: | ||
==== Links ==== | ==== Links ==== | ||
+ | |||
+ | * :!: 2022: OpenWRT snapshot builds were disabled at some point, see https:// | ||
* [[https:// | * [[https:// | ||
Line 34: | Line 36: | ||
ssh ' | ssh ' | ||
- | passwd | + | |
- | opkg update && opkg install luci && sync | + | opkg update && opkg install luci irqbalance nano && sync |
- | ====== Wireless AP ====== | + | ====== Wireless AP Mode ====== |
* [[https:// | * [[https:// | ||
===== Network ===== | ===== Network ===== | ||
+ | |||
+ | * [[https:// | ||
* Sets router IP to '' | * Sets router IP to '' | ||
Line 57: | Line 61: | ||
< | < | ||
/ | / | ||
+ | |||
+ | ====== irqbalance ====== | ||
+ | |||
+ | * https:// | ||
+ | |||
+ | nano '/ | ||
====== LuCI ====== | ====== LuCI ====== | ||
Line 64: | Line 74: | ||
===== Startup ===== | ===== Startup ===== | ||
- | * http:// | ||
* https:// | * https:// | ||
* :!: This is seemingly required in order to keep latency at a consistent 0.2ms on Ethernet | * :!: This is seemingly required in order to keep latency at a consistent 0.2ms on Ethernet | ||
- | < | + | * http://192.168.1.2/ |
- | # Put your custom commands here that should be executed once | + | |
- | # the system init finished. By default this file does nothing. | + | |
- | echo ' | + | < |
- | + | echo ' | |
- | exit 0</ | + | |
==== Verify ==== | ==== Verify ==== | ||
Line 84: | Line 90: | ||
< | < | ||
- | ===== Quad9 DNS ===== | + | ===== Scheduled Reboot |
- | * [[https://quad9.net/service/service-addresses-and-features#ecssec|Secured w/ECS]] | + | * https://www.albertogonzalez.net/how-to-reboot-nightly-your-openwrt-router/ |
+ | * https:// | ||
+ | |||
+ | * http:// | ||
+ | |||
+ | < | ||
+ | # Restart 3:32 AM | ||
+ | 32 3 * * * sleep 70 && touch /etc/banner && reboot</ | ||
+ | |||
+ | ===== 1.1.1.1 DNS ===== | ||
+ | |||
+ | * https:// | ||
* See [[notes: | * See [[notes: | ||
- | < | + | < |
- | < | + | |
- | < | + | < |
- | < | + | |
+ | < | ||
+ | |||
+ | < | ||
===== Wireless ===== | ===== Wireless ===== | ||
Line 100: | Line 120: | ||
* Country Code: US | * Country Code: US | ||
* Channel: 6 | * Channel: 6 | ||
- | * Width: | + | * Width: |
* Encryption: WPA2-PSK CCMP AES | * Encryption: WPA2-PSK CCMP AES | ||
Line 113: | Line 133: | ||
< | < | ||
+ | |||
+ | ===== Firewall ===== | ||
+ | |||
+ | * See [[notes: | ||
+ | |||
+ | ====== Recovery ====== | ||
+ | |||
+ | ===== mtd ===== | ||
+ | |||
+ | * https:// | ||
+ | * OpenWRT -> Linksys | ||
+ | |||
+ | ==== Download Stock Firmware ==== | ||
+ | |||
+ | * https:// | ||
+ | * '' | ||
+ | |||
+ | ssh ' | ||
+ | |||
+ | wget ' | ||
+ | |||
+ | ==== Check Current Firmware Partition ==== | ||
+ | |||
+ | * 11 = '' | ||
+ | * 13 = '' | ||
+ | * :!: Flash operations should be done on the kernel **not** mentioned in the following command ((so if '' | ||
+ | |||
+ | cat '/ | ||
+ | |||
+ | ==== Erase Non-current Firmware Partition ==== | ||
+ | |||
+ | mtd erase ' | ||
+ | |||
+ | mtd erase ' | ||
+ | |||
+ | ==== Flash Stock Firmware ==== | ||
+ | |||
+ | mtd write ' | ||
+ | |||
+ | mtd write ' | ||
+ | |||
+ | ==== Boot Stock Firmware ==== | ||
+ | |||
+ | * 1 = '' | ||
+ | * 2 = '' | ||
+ | |||
+ | fw_setenv ' | ||
+ | |||
+ | fw_setenv ' | ||
+ | |||
+ | sync && reboot | ||
/var/www/wiki/data/attic/devices/linksys_ea6350_v3.1631175072.txt.gz · Last modified: 2021/09/09 04:11 by Sean Rhone